Battery connection cable kit-Inverter Pylontech...
Battery connection cable kit-Inverter Pylontech 2 m 070004

Battery connection cable kit-Inverter Pylontech 2 m 070004

PackCablePylontech
€19.48
Tax included

The Connection Cable Kit for batteries Pylontech 070004 brings together all the wiring necessary to join a bank of lithium batteries Pylontech with the inverter: a 2 m positive power cable, a 2 m negative power cable and a 3.5 m RJ45 communication cable. Thanks to him, the battery can deliver and receive energy from inverter And, at the same time, exchange with it the information of your management system (BMS), such as the state of charge, tensions and current limits, so that the load and discharge are always carried out within the safe parameters. The power cables are manufactured with Wiring material according to the UL 758 (AWM) standard, designed for conductors of electrical equipment. It is the simplest way to complete the installation of a battery Pylontech Low voltage with ordered wiring, adequate length and designed for this use.

 

Detailed technical characteristics

Kit content

  • Positive power cable: 1 unit, length 2 m
  • Negative power cable: 1 unit, length 2 m
  • Communication cable RJ45: 1 unit, length 3.5 m

General data

  • Reference: 070004
  • Use: connection Power and communication batteries Pylontech and the inverter
  • Drivers material: wiring UL 758 (Appliance Wiring Material)
  • Communication: The RJ45 cable included It is not valid for CAN communication

Benefits of the Connection Cable Kit Pylontech

A lithium battery is as reliable as its connection. A poorly dimensioned or improvised wiring can cause voltage drops, warm-ups or communication errors between the battery and the inverter. This kit brings together in a single pack the three cables that any installation with batteries needs Pylontech of low voltage.

Power and communication in a single pack

The kit includes both the power cables (positive and negative) as the communication cable. Thus, it is not necessary to look for each component separately or manufacture tailor-made cables for a standard connection, which saves time in the installation and reduces the risk of errors.

Lengths designed for an orderly installation

The 2 m of the power cables allow the battery to be placed next to hybrid inverter With a short tour, it is recommended in continuous current to limit losses. The communication cable, 3.5 m, offers additional margin to take the BMS signal to the port of the inverter.

Communication BMS-inverter

The lithium batteries Pylontech incorporate a management system that communicates to inverter The battery status. This communication allows the inverter Automatically adjust the load and download, protecting the cells and taking advantage of the stored energy.

Certified Wiring Material

The drivers are manufactured with Wiring material according to the UL 758 (AWM) standard, Specific for the wiring of electrical equipment, which provides confidence in the quality of isolation and the construction of the cable.

How to use the kit in your installation

A kit by battery bank

Batteries Pylontech they connect each other in parallel forming a bank, and it is the master battery the one that connects with the inverter. For that, in a typical installation it is used A Cable Kit by bank, while the connections between modules are made with the interconnection wiring provided for it.

Check the communication protocol of the inverter

The RJ45 cable included It is not valid for CAN communication. Before installation, check which protocol uses your inverter with batteries Pylontech; If you work through CAN, you will need a specific communication cable for that model.

Continuous circuit protection

Between the battery and the inverter it is advisable to install a Control of DC (fuse or disconnector) sized according to the system stream, following the indications of the battery manufacturers and the inverter.

Complete your system

If you are riding a self-consumption installation with storage, on our website you will find solar panels, inverters solar compatible with Pylontech and Solar kits complete.

On Tienda Solar We have batteries Pylontech and all its accessories, and in the Single store bloga You can consult purchase guides and technical items prepared by experts.

Frequently Asked Questions (FAQ)

1. What does the cable kit include?

Includes A 2 m positive power cable, A negative power cable of 2 m and A 3.5 m RJ45 communication cable To connect the battery Pylontech with the inverter.

2. Can I use the communication cable with a inverter that works by Can?

No. The RJ45 cable included in this kit It is not valid for CAN communication. If you inverter communicates with the battery by CAN, you will need a specific communication cable for that inverter.

3. Do I need a kit for each battery?

Normally no. The kit connects the battery bank with the inverter through the master battery, so in a typical installation it is enough A Banco Kit. The bank's modules connect with their own interconnection wiring.

4. What do I do if 2 meters are not enough?

Ideally, place the battery near the inverter To keep the current current wiring short. If the distance is greater, the installer must dimension with longer cables with the appropriate section to the system stream to avoid voltage drops and warm-ups.

5. Is it compatible with my battery Pylontech?

The kit is designed for batteries Pylontech low-voltage. As there are different models and generations, we recommend consulting with our technical team indicating the exact model of your battery and your inverter Before purchase.

6. Should I install some protection between the battery and the inverter?

Yes, it is advisable to install a Control of DC, like a fuse or a disconnector, sized according to the maximum current of the system and following the indications of the manufacturers of the battery and the inverter.

Customers who bought this product also bought: