This shop uses own and third party cookies to improve our services and your browsing experience. If you continue browsing, we consider that you accept its use. More information..

OK

Brands

Accessories

What is included in accessories category?

The accessories are all those components or small products beyond solar panels, inverters, batteries or mounting system necessary to install the complete assembly of a residential or commercial solar installation either grid tied or off-grid. In thissectionyou will find elements such as combination boxes of series of modules (strings) in continuous, continuous disconnecting switches in load or other small components such as solar connectors or solar cable. Most of these components complement those solar Kits that do not have them but can also be purchased independently as spare parts. The accessories are also part of the so-called “Balance of System” (BOS) that includes all the elements with a lower specific weight (solar panels, inverters or batteries) of a photovoltaic solar installation.

Accessories

Active filters

  • New

Communication Cable Axpert-Pylontech

€29.11

These cables are ideal for connecting your LV Pylontech batteries to an inverter from the Voltronic Axpert series, thus boosting energy storage from solar panels, wind turbines or other electricity generating sources. 

  • New

Enphase Envoy S Metered

€424.51

Communication bridge Enphase Envoy S Metered. It provides detailed information on energy consumption and load management. System that guarantees the maintenance and remote management of your Enphase installation.

It communicates with the Q Relay to isolate the phase and neutral, if necessary, depending on the state of the electrical network.

  • New

Enphase Q Relay Single Phase

€77.19

Enphase disconnect relay to disconnect the microinverters from your Enphase installation in case of network anomalies. When the voltage returns to normal and the mains frequency stabilizes again, the relay automatically reconnects the system. The Q Relay communicates with the Envoy S Meter to isolate the phase and neutral, if necessary, depending on the state of the power grid.

It is necessary to have one piece per installation.

  • New

Enphase Single Phase Female Connector

€14.47

These connectors allow you to connect your Q Cable Enphase to your panels without the need for complex wiring. 

You can make connections from any open connector and centre splice any section of cable within the circuit boundaries.

  • New

Enphase Single Phase Male Connector

€14.47

These connectors allow you to connect your Q Cable Enphase to your panels without the need for complex wiring. 

You can make connections from any open connector and centre splice any section of cable within the circuit boundaries.

  • New

Q Cable Enphase 1.7m Single Phase

€30.09

These cables are ideal for connecting your panels to Enphase microinverters. They are the seventh generation of the IQ system. These cables have a simple and reliable design.

For your Enphase installation it is necessary to have one of these cables for each panel in your installation.

  • New

Victron VE Direct Bluetooth Smart Dongle Module

€47.74

Compatible Bluetooth module for Victron

Small Bluetooth module compatible with almost all Victron products with an integrated VE.Direct port. This device will allow you to monitor your installation via a Bluetooth mobile device. Bluetooth module easy to connect to Victron controllers.

  • New

Pocket Wifi SAJ eSolar R5

€63.00

Compatible Wifi module for SAJ R5 inverters

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

Small WI-FI module compatible with SAJ solar inverters of the R5 series. This device will allow you to monitor the output of the solar panels and your solar inverter from any location via the inverter\'s mobile app. WI-FI module easy to connect to the inverter and the internet.

  • New

Pocket Wifi SAJ eSolar H1

€107.98

Compatible Wifi module for SAJ H1 inverters

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

Small WI-FI module compatible with SAJ solar inverters of the H1 series. This device will allow you to monitor the output of the solar panels and your solar inverter from any location via the inverter\'s mobile app. WI-FI module easy to connect to the inverter and the internet.

  • New

BackUp SolaX Power X3 MateBox

€1,482.97

Compatible Back-Up module for SolaX X3 inverters

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

Small BackUp module compatible with three-phase X3-Hybrid SolaX solar inverters. This device will allow you to easily switch between network connection and off-grid modes. Easy to connect BackUp module. Alternative to Backup EPS Box X3.

  • New

BackUp SolaX Power X1 MateBox

€823.88

Compatible Back-Up module for SolaX X1 inverters

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

Small BackUp module compatible with single-phase X1-Hybrid SolaX solar inverters. This device will allow you to easily switch between network connection and off-grid modes. Easy to connect BackUp module. Alternative to Backup EPS Box X1.

  • New

BackUp SolaX Power X3 EPS Box

€411.93

Compatible Back-Up module for SolaX X3 inverters

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

Small BackUp module compatible with three-phase X3-Hybrid SolaX solar inverters. This device will allow you to easily switch between network connection and off-grid modes. Easy to connect BackUp module. Alternative to Backup Matebox X3.

  • New

BackUp SolaX Power X1 EPS Box

€313.85

Compatible Back-Up module for SolaX X1 inverters

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

Small BackUp module compatible with single-phase X1-Hybrid SolaX solar inverters. This device will allow you to easily switch between network connection and off-grid modes. Easy to connect BackUp module. Alternative to Backup Matebox X1.

  • New

Tigo Optimizer TS4-A-O

€50.69

Optimizer of compact measures and easy installation, high efficiency and safety.

The Tigo TS4-A-O is a solar panel optimizer that offers SMART technology to standard solar panels. With the Tigo optimizer you can improve the energy efficiency of your solar installation by improving the performance of your solar panels. Adding this optimizer to each of your dashboards will allow you to keep track of each dashboard when connecting to the cloud. 

The Tigo TS4-A-O uses UHD-Core technology and is compatible with solar panels up to 700W and 15A.

  • New

Wattmeter smart meter TS 100A for Fronius Single-Phase

€92.93

Fronius Smart Meter TS Single Phase Wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Fronius Single Phase Wattmeter, model Smart Meter TS up to 100A, is a wattmeter that allows to control the different energy flows, both solar generation and consumption of the building where it is installed. The device also records the consumption and generation curve in order to optimize the solar installation. This wattmeter allows remote and accurate power limitation. The Fronius Smart Meter TS is compatible with the single-phase inverters of the Primo, ECO, and Galvo series.

ONLY AVAILABLE WITH THE PURCHASE OF FRONIUS STRING INVERTERS.

  • New

Wattmeter smart meter TS 65A for Fronius Three-Phase

€227.68

Fronius Smart Meter TS Single Phase Wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Fronius Single Phase Wattmeter, model Smart Meter TS up to 65A, is a wattmeter that allows to control the different energy flows, both solar generation and consumption of the building where it is installed. The device also records the consumption and generation curve in order to optimize the solar installation. This wattmeter allows remote and accurate power limitation. The Fronius Smart Meter TS is compatible with the three-phase inverters of the ECO, Symo, Symo Hybrid and Galvo series.

ONLY AVAILABLE WITH THE PURCHASE OF FRONIUS STRING INVERTERS.

  • New

Wattmeter smart meter TS 5kA for Fronius Three-Phase

€227.68

Fronius Smart Meter TS Single Phase Wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Fronius Single Phase Wattmeter, model Smart Meter TS up to 5kA, is a wattmeter that allows to control the different energy flows, both solar generation and consumption of the building where it is installed. The device also records the consumption and generation curve in order to optimize the solar installation. This wattmeter allows remote and accurate power limitation. The Fronius Smart Meter TS is compatible with the three-phase inverters of the ECO, Symo, Symo Hybrid and Galvo series.

ONLY AVAILABLE WITH THE PURCHASE OF FRONIUS STRING INVERTERS.

  • New

Wattmeter smart meter TS 63A for Fronius Three-Phase

€227.68

Fronius Smart Meter TS Single Phase Wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Fronius Single Phase Wattmeter, model Smart Meter TS up to 63A, is a wattmeter that allows to control the different energy flows, both solar generation and consumption of the building where it is installed. The device also records the consumption and generation curve in order to optimize the solar installation. This wattmeter allows remote and accurate power limitation. The Fronius Smart Meter TS is compatible with the three-phase inverters of the ECO, Symo, Symo Hybrid and Galvo series.

ONLY AVAILABLE WITH THE PURCHASE OF FRONIUS STRING INVERTERS.

  • New

Red solar cable 6 mm² (100 meters)

€142.40

Double insulated red cable for solar applications of 6 mm² section (price for 100 meters)

Red electric cable for solar applications of 6 mm². Double insulated cable specifically designed for assembly, design and installation of residential, commercial or industrial solar systems. Suitable for design of up to 1000V in the continuous part, capable of operating between -40ºC and 120ºC and operating current of 70A in the air It has an insulating layer of UV rays, is halogen free and complies with CE certification.

  • New

Black solar cable 6 mm² (100 meters)

€142.40

Double insulated black cable for solar applications of 6 mm² section (price for 100 meters)

Red electric cable for solar applications of 6 mm². Double insulated cable specifically designed for assembly, design and installation of residential, commercial or industrial solar systems. Suitable for design of up to 1000V in the continuous part, capable of operating between -40ºC and 120ºC and operating current of 70A in the air It has an insulating layer of UV rays, is halogen free and complies with CE certification.

  • New

Black solar cable 6 mm² (50 meters)

€71.20

Double insulated black cable for solar applications of 6 mm² section (price for 50 meters)

Red electric cable for solar applications of 6 mm². Double insulated cable specifically designed for assembly, design and installation of residential, commercial or industrial solar systems. Suitable for design of up to 1000V in the continuous part, capable of operating between -40ºC and 120ºC and operating current of 70A in the air It has an insulating layer of UV rays, is halogen free and complies with CE certification.

HV Lithium Battery Cable Pack - Pylontech

€22.24

These cables are ideal for connecting your HV Pylontech batteries to an inverter, thus boosting energy storage from solar panels, wind turbines or other electricity generating sources. The pack includes 1 x 2 meter positive power cable, 1 x 2 meter negative power cable and 1 x 3.5 meter RJ45 communication cable (not valid for CAN communication)

Powercable Lithium Battery Cable Pack - DYNESS

€40.95

These cables are ideal for connecting your Dyness batteries to an inverter, thus boosting energy storage from solar panels, wind turbines or other electricity generating sources. The pack includes 1 x 2 meter positive power cable and 1 x 2 meter negative power cable. Section 25 mm2, maximum current of 120 A.

SolarEdge Power Optimizer P300

€48.99

SolarEdge power optimiser for 60-cell modules. It is a DC/DC converter that connects to each solar module, turning them into smart modules. These optimisers increase the power output of photovoltaic systems by constantly monitoring the maximum power point (MPPT) of each individual module. In addition, the power optimisers monitor the performance of each module and communicate performance data to the SolarEdge monitoring platform for improved and cost-effective maintenance at the module level.

These optimisers are specifically designed for SolarEdge residential inverters. It is compatible with bifacial modules.

25 year warranty.

SolarEdge Power Optimizer P601

€90.88

SolarEdge power optimiser for modules up to 14A. It is a DC/DC converter that is connected to each solar module, turning them into smart modules. These optimisers increase the power output of photovoltaic systems by constantly monitoring the maximum power point (MPPT) of each individual module. In addition, the power optimisers monitor the performance of each module and communicate performance data to the SolarEdge monitoring platform for improved and cost-effective maintenance at the module level.

These optimisers are specifically designed for SolarEdge residential inverters. It is compatible with bifacial modules.

25 year warranty.

SolarEdge Power Optimizer S500

€73.91

SolarEdge power optimiser for modules up to 500W. It is a DC/DC converter that is connected to each solar module, turning them into smart modules. These optimisers increase the power output of photovoltaic systems by constantly monitoring the maximum power point (MPPT) of each individual module. In addition, the power optimisers monitor the performance of each module and communicate performance data to the SolarEdge monitoring platform for improved and cost-effective maintenance at the module level.

The SolarEdge S series power optimisers are specifically designed for SolarEdge residential inverters. It is compatible with bifacial modules.

25 year warranty.

SolarEdge Power Optimizer S440

€68.93

In stock

SolarEdge power optimiser for modules up to 440W. It is a DC/DC converter that is connected to each solar module, turning them into smart modules. These optimisers increase the power output of photovoltaic systems by constantly monitoring the maximum power point (MPPT) of each individual module. In addition, the power optimisers monitor the performance of each module and communicate performance data to the SolarEdge monitoring platform for improved and cost-effective maintenance at the module level.

The SolarEdge S series power optimisers are specifically designed for SolarEdge residential inverters. It is compatible with bifacial modules.

25 year warranty.

Wattmeter for Huawei Three-Phase

€180.88

Huawei Smart Power Three-Phase Wattmeter DTSU666-H

ONLY AVAILABLE WITH THE PURCHASE OF HUAWEI THREE-PHASE INVERTER

The single-phase wattmeter model DDSU666-H, is a wattmeter that allows you to configure the calibrated 0 discharge. The device is calibrated to measure the energy coming in or going out of the whole house. This wattmeter is used with Huawei inverters.

Wattmeter SUNNY HOME MANAGER 2.0

€704.32

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Sunny Home Manager 2.0 enables the most efficient use of solar energy in the home. It stands out for its innovation, simplicity, transparency and flexibility.

It reduces electricity costs and optimises PV self-consumption. To do so, it measures the output of PV generation, purchased electricity and grid feed-in and provides an overview of all relevant energy flows in the household. Based on local PV generation forecasts and the measured household consumption profile, the self-learning device provides the user with energy-related recommendations for action. The operation of the controlled devices is coordinated to optimise the use of the self-generated solar energy.

Warranty of 2 years.

Wattmeter SMA ENERGY METER-20

€428.55

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The SMA Energy Meter is a high-performance meter for intelligent energy management in photovoltaic systems with SMA devices. Stands out for its simplicity, flexibility and high performance.

It is capable of calculating the electrical measured values communicated via Ethernet in the local network. The PV generation of other PV inverters and data on grid feed-in and purchased electricity can be communicated to SMA systems with a high level of accuracy. The integration of the SMA Energy Meter establishes an ideally coordinated system configuration that guarantees the highest yield and stability with the best cost savings and increased self-consumption. 

2-year warranty.

Resin DIY Fis green

€24.45

El anclaje químico ecológico fischer está compuesto por material reciclado en más de un 50%. Alcanza valores similares a una resina viniléster sin estireno, certificado para aplicaciones en ladrillo y hormigón. - 1x Taco químico FIS GREEN 300ml - 2x Cánulas mezcladoras

MS liquid 1 kg brown

€19.95

Para impermeabilizar la superficie en la que se ha fijado el anclaje solar se debe utilizar: - 1x Pintura impermeabilizante MS Marrón Cubo 1kg

Broca SDS short Pointer M 16/100/400

€55.22

Para poder fijar las fijaciones solares se necesita una broca para perforar la superficie en la que se debe fijar: - 1x Broca 16/100/400 para ladrillo hueco y hormigón celular

Victron GX Touch 50

€225.68

In stock

This all-new communications hub allows you to be in control of your system anytime, anywhere and maximise performance. Simply connect via the Victron Remote Management (VRM) portal, or access it directly via the standalone GX Touch multifunction display or the VictronConnect app thanks to the built-in Bluetooth function. This latest addition to the GX range combines all the best of connectivity, redefining smart energy solutions in every aspect.

You can watch the new video explaining everything you need to know about the installation of the new Cerbo GX and GX Touch 50 products.

Victron Cerbo GX

€331.58

In stock

This all-new communications hub allows you to be in control of your system anytime, anywhere and maximise performance. Simply connect via the Victron Remote Management (VRM) portal, or access it directly via the standalone GX Touch multifunction display or the VictronConnect app thanks to the built-in Bluetooth function. This latest addition to the GX range combines all the best of connectivity, redefining smart energy solutions in every aspect.

You can watch the new video explaining everything you need to know about the installation of the new Cerbo GX and GX Touch 50 products.

Victron VE.Can to CAN-bus BMS type B Cable 5m

€17.83

Use this cable to connect a CAN-bus enabled battery of a brand other than Victron to a Victron system. There are two types, A and B. See the manual for more information on which cable to use depending on the battery brand on Victron\'s website: Manual

Victron Color Control GX

€526.88

The Color Control GX is the communications hub of your installation. It provides real-time information at a glance and allows you to control all the products connected to it. You can control the entire system, from virtually anywhere in the world, by accessing your Color Control GX through the free Victron Remote Management (VRM) portal.

Wattmeter smart meter TS 63A for Fronius Single-Phase

€88.09

Fronius Smart Meter TS Single Phase Wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Fronius Single Phase Wattmeter, model Smart Meter TS up to 63A, is a wattmeter that allows to control the different energy flows, both solar generation and consumption of the building where it is installed. The device also records the consumption and generation curve in order to optimize the solar installation. This wattmeter allows remote and accurate power limitation. The Fronius Smart Meter TS is compatible with the single-phase inverters of the Primo, ECO, and Galvo series.

ONLY AVAILABLE WITH THE PURCHASE OF FRONIUS STRING INVERTERS.

Kit communcations Axpert MKS/KS/KING

€79.07

Parallel cable connection kit MKS/KS/KING

ONLY AVAILABLE BY PURCHASING AN AXPERT INVERTER

Small kit for parallel connection of Voltronic inverters of the AXPERT MKS, KS and King series. Two of these devices allow two solar inverters to be connected in parallel and to communicate with each other. The parallel connection kit includes a PCD (printed circuit board), a power cable to supply the circuitry and a VGA communication cable. 

Pocket Wifi Solax

€42.00

Compatible Wifi module for SolaX inverters

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

Small WI-FI module compatible with SolaX solar inverters of the X1 Mini, X1 Air, X1 Boost, X3 Three-phase, X-Hybrid Three-phase and third generation X-Hybrid series. This device will allow you to monitor the output of the solar panels and your solar inverter from any location via the inverter\'s mobile app. WI-FI module easy to connect to the inverter and the internet.

LV Lithium Battery Cable Pack - PYLONTECH

€20.55

These cables are ideal for connecting your Pylontech batteries to an inverter, thus boosting energy storage from solar panels, wind turbines or other electricity generating sources. The pack includes 1 x 2 meter positive power cable, 1 x 2 meter negative power cable and 1 x 3.5 meter RJ45 communication cable (not valid for CAN communication)

Wattmeter for Huawei Single-Phase

€93.42

Chint DDSU666 Single Phase Wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Chint single-phase wattmeter, model DDSU666, is a wattmeter that allows you to set up the calibrated zero feed-in ("vertido cero"). The device is calibrated to measure the energy that arrives or leaves the whole house. This wattmeter is used with the Huawei inverters.

Wattmeter GoodWe Smart Meter GM1000

€260.93

GoodWe Smart meter single-phase wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The GoodWe single-phase wattmeter is a wattmeter that allows you to configure the calibrated 0 discharge as well as measure the amount of energy consumed from the grid and the energy generated by the installation. GoodWe wattmeter configurable with all GoodWe single-phase grid-connected and hybrid grid-connected inverters. The device allows you to know exactly the energy balances of your home, electrical grid and self-consumption solar installation.

This wattmeter is compatible with the SEMS monitoring system of GoodWe inverters.

Wattmeter for Solax X1-Boost, X1-Hybrid and SAJ R5

€97.43

Chint DDSU666 Single Phase Wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Chint single-phase wattmeter, model DDSU666, is a wattmeter that allows you to set up the calibrated zero feed-in ("vertido cero"). The device is calibrated to measure the energy that arrives or leaves the whole house. This wattmeter is used with the SolaX X1-Boost and X1-Hybrid inverters and the SAJ R5 inverters.

Wattmeter for Solax X1-Boost, X1-Hybrid and SAJ R5

€182.18

Chint DDSU666 Single Phase Wattmeter

ONLY AVAILABLE WITH THE PURCHASE OF THE INVERTER

The Chint single-phase wattmeter, model DDSU666, is a wattmeter that allows you to set up the calibrated zero feed-in ("vertido cero"). The device is calibrated to measure the energy that arrives or leaves the whole house. This wattmeter is used with the SolaX X1-Boost and X1-Hybrid inverters and the SAJ R5 inverters.

Wattmeter for Solax X1-Boost, X1-Hybrid and SAJ R5

€65.60

Chint DDSU666 Single Phase Wattmeter

The Chint single-phase wattmeter, model DDSU666, is a wattmeter that allows you to set up the calibrated zero feed-in ("vertido cero"). The device is calibrated to measure the energy that arrives or leaves the whole house. This wattmeter is used with the SolaX X1-Boost and X1-Hybrid inverters and the SAJ R5 inverters.

Male photovoltaic connector Multicontact for 4 and 6 mm2

€2.17

MC-4 Male Multicontact photovoltaic connector for section 4 and 6 mm2 cables

MC-4 male photovoltaic connector of the renowned Multicontact brand for section cables from 4 to 6 mm2. The connector makes it easy to close the DC part of electrical circuit from theend of each string (series of modules) to the corresponding input of the inverter. Suitable for installations up to 1000V and perfect for residential, industrial or commercial systems. The connector also includes the metal rod to crimpit with the solar cable.

Easy to assemble system that guarantees the safety of the installation avoid in high resistance points and potential electric arcs in one of the most critical points of the assembly

Female photovoltaic connector Multicontact for 4 and 6 mm²

€2.65

MC-4 Female Multicontact photovoltaic connector for section 4 and 6 mm2 cables

MC-4 female photovoltaic connector of the renowned Multicontact brand for section cables from 4 to 6 mm2. The connector makes it easy to close theDC part ofelectrical circuit from the end of each string (series of modules) to the corresponding input of the inverter. Suitable for installations up to 1000V and perfect for residential, industrial or commercial systems. The connector also includes the metal rod to crimp it with the solar cable.

Easy to assemble system that guarantees the safety of the installation avoiding high resistance points and potential electric arcs in one of the most critical points of the assembly.

Red solar cable 6 mm² (500 meters)

€712.00

Double insulated red cable for solar applications of 6 mm² section (price for 500 meters)

Red electric cable for solar applications of 6 mm². Double insulated cable specifically designed for assembly, design and installation of residential, commercial or industrial solar systems. Suitable for design of up to 1000V in the continuous part, capable of operating between -40ºC and 120ºC and operating current of 70A in the air It has an insulating layer of UV rays, is halogen free and complies with CE certification.

Black solar cable 6 mm² (25 meters)

€35.60

Double insulated black cable for solar applications of 6 mm² section (price for 25 meters)

Red electric cable for solar applications of 6 mm². Double insulated cable specifically designed for assembly, design and installation of residential, commercial or industrial solar systems. Suitable for design of up to 1000V in the continuous part, capable of operating between -40ºC and 120ºC and operating current of 70A in the air It has an insulating layer of UV rays, is halogen free and complies with CE certification.